How to Replace an RV Water Pump with Amazon Products

Hey there, fellow RV enthusiasts! If you’ve found yourself in the middle of your RV adventures with a water pump that’s stopped working, don’t worry—you can easily replace it yourself with the right tools and a little guidance. In this DIY tutorial, I’ll walk you through the process of replacing an RV water pump, using some of the top-rated products on Amazon. It’s easier than you think, and you’ll save money on expensive repairs. Let’s get started!

Why Replace Your RV Water Pump?

Your RV water pump is the heart of your water system. It draws water from your fresh water tank and pushes it into your pipes so you can take a shower, wash dishes, and flush the toilet. If your pump stops working, it can seriously disrupt your RV life. It could be caused by wear and tear, a clogged filter, or electrical issues, but often, replacing the pump is the most reliable solution.

---

What You’ll Need to Replace Your RV Water Pump

Before we dive into the steps, let’s make sure you have the right products to get the job done. Below, I’ve listed the top-rated RV water pumps and accessories you can easily find on Amazon.

1. Best RV Water Pump: Shurflo 4008-101-E65 3.0 Revolution Water Pump

Shurflo is known for making reliable, durable water pumps, and this model is no exception. It’s a 3.0 GPM pump with a high-flow rate, making it perfect for most RVs. This pump runs quietly and is easy to install, making it a top choice for DIY enthusiasts. It also has a built-in check valve to prevent backflow, ensuring a smooth water flow.

2. Best RV Water Pump Strainer: Shurflo 255-313

A good strainer ensures that debris doesn’t clog your pump. This one is specifically designed for RV use, easy to clean, and works seamlessly with Shurflo pumps. It’s a must-have to extend the life of your new pump.

---

Step-by-Step Guide to Replacing Your RV Water Pump

Step 1: Gather Your Tools & Turn Off Water Supply

Start by turning off your RV’s water supply and disconnecting the power. You don’t want any surprises while working with water and electricity. If your RV is connected to shore power, disconnect it to avoid any electrical hazards.

Step 2: Locate the Old Pump

Next, locate your water pump. Most RV pumps are under the sink, in a storage compartment, or near the water tank. If you’re unsure of where it is, consult your RV’s manual to find the exact location.

Step 3: Disconnect the Old Pump

Start by unscrewing or unfastening any brackets or screws that are holding your pump in place. Then, disconnect the water lines that are attached to the pump. Be sure to have a towel or bucket ready in case there’s any residual water in the lines.

Pro Tip: Take a photo of the old pump’s connections or make a diagram so you know how to attach the new one.

Step 4: Install the New Pump

Now that the old pump is out, it’s time to install the new one. Begin by attaching the water supply and output hoses to the new pump. Ensure that the inlet and outlet are properly connected to avoid any leaks. Secure the pump using the mounting brackets, making sure it’s stable and won’t move around while the RV is in motion.

Step 5: Connect the Electrical Wires

Your RV pump will have electrical connections that you’ll need to wire into place. Follow the manufacturer instructions that come with your new pump (like the Shurflo 4008-101-E65) to connect the wires to the power supply. If you’re unsure about the electrical work, consult a professional to avoid damaging your RV’s electrical system.

Step 6: Test the New Pump

Once everything is hooked up, turn the water supply back on and test your pump by turning on the water faucets in your RV. If everything works correctly—no leaks, no strange noises, and consistent water flow—congratulations, you’ve just installed a new water pump!

---

_{This post contains affiliate links to Amazon. If you make a purchase through these links, I may earn a small commission at no extra cost to you. This helps me continue creating useful content like this for you!}